Introduction
Every workshop, every factory, every home has a collection of spray cans — one for rust, one for lubrication, one for cleaning, one for water protection. But what if one can could do it all?
Multispray by Soudal is precisely that: an 8-in-1 multi-purpose spray that handles most common maintenance tasks with a single product. Available through Soudal Pakistan, it’s become the go-to solution for mechanics, technicians, and DIY enthusiasts who value efficiency and performance.
What is Multispray?
Multispray is a high-quality universal spray formulated from a special mixture of mineral oils. It comes in a convenient 400 ml aerosol can with a 360° valve that sprays at any angle — even upside down.
But what makes Multispray truly special is its 8-fold action:
1. Rust dissolver
2. Lubricant
3. Cleaner
4. Water repellent
5. Penetrating oil
6. Corrosion resistant
7. Contact spray
8. Shock spray
The 8 Actions Explained
1. Rust Dissolver
Multispray penetrates rust layers, breaking the bond between rust and metal. Spray on rusted bolts, nuts, or components, wait 5–10 minutes, and watch rust loosen for easy removal.
2. Lubricant
The fine oil film reduces friction on moving parts:
· Hinges and door mechanisms
· Chains and sprockets
· Roller bearings and axles
· Conveyor belts and pulleys
· Slide mechanisms
3. Cleaner
Multispray dissolves and removes:
· Dirt and grime
· Light grease and oil
· Contaminants from surfaces
· Residues from machinery
4. Water Repellent
The protective film repels moisture, preventing:
· Water ingress into electrical components
· Moisture damage to metal surfaces
· Corrosion in humid environments
· Short circuits in electrical systems
5. Penetrating Oil
With its low viscosity (1 mPa.s), Multispray seeps into the tightest spaces:
· Between threaded connections
· Into seized mechanisms
· Under rust layers
· Into cable conduits
6. Corrosion Resistant
The protective film left after application shields surfaces from:
· Atmospheric corrosion
· Humidity and moisture
· Salt spray (coastal areas)
· Chemical exposure
7. Contact Spray
Multispray safely cleans and protects electrical contacts:
· Switches and relays
· Battery terminals
· Electrical connectors
· Circuit boards (with care)
8. Shock Spray
The rapid evaporation creates a cooling effect that:
· Contracts metal parts for fitting
· Helps loosen tight components
· Provides temporary cooling
· Aids in thermal troubleshooting
Primary Applications in Pakistan
Automotive Workshops
· Loosening rusted bolts and nuts
· Lubricating door hinges and locks
· Cleaning battery terminals
· Protecting electrical connections
· Freeing seized brake components
Industrial Maintenance
· Maintaining conveyor systems
· Lubricating roller bearings
· Protecting machinery from corrosion
· Cleaning production equipment
· Maintaining pneumatic systems
Home and DIY
· Silencing squeaky doors
· Maintaining bicycle chains
· Protecting garden tools
· Cleaning switch contacts
· Lubricating locks and latches
Marine Applications
· Protecting boat fittings from salt corrosion
· Lubricating marine hardware
· Waterproofing electrical connections
· Maintaining winches and pulleys
Application Best Practices
Step 1: Preparation
· Identify the task (which of the 8 actions you need)
· For cleaning: remove loose dirt first
· For rusted parts: ensure access to affected area
· Shake can well before use
Step 2: Application
· Hold can approximately 20 cm from surface
· Spray evenly, covering the area
· For rust dissolution: wait 5–10 minutes
· For lubrication: apply and work the mechanism
Step 3: After Application
· Allow solvent to evaporate (leaves protective film)
· For electrical use: ensure complete evaporation before power-up
· Wipe excess if needed
· Dispose of rags properly
Special Applications
As rust dissolver:
Spray generously on rusted parts. Wait 5–10 minutes. Tap gently or attempt removal. Reapply if needed.
As shock spray:
Spray on overheated components or to shrink metal parts for assembly. Use with caution.
On electrical contacts:
Spray briefly, allow to evaporate completely, then restore power.
Frequently Asked Questions (FAQs)
Q1: Is Multispray safe on all plastics?
Does not attack rubber, plastics or metals. However, with thousands of plastic formulations, it’s wise to test on an inconspicuous area first, especially on sensitive or aged plastics.
Q2: Can it be used as a WD-40 alternative?
Yes, Multispray performs similar functions — and adds the shock spray action — while being silicone-free. Many professionals prefer it specifically because it won’t contaminate surfaces for later painting or bonding.
Q3: How long does the protection last?
The protective film remains until mechanically removed or worn away. For outdoor or high-wear applications, reapply periodically. The corrosion-resistant layer provides ongoing protection.
Q4: Can it be used on electrical equipment while powered?
No. Always disconnect power before spraying electrical components. Allow spray to evaporate completely before reconnecting power.
Q5: What’s the difference between Multispray and contact cleaners?
Multispray combines cleaning with protection. While it cleans contacts effectively, it also leaves a protective film that prevents future corrosion. Pure contact cleaners may clean but don’t provide ongoing protection.
Conclusion
Multispray isn’t just another spray can — it’s a complete maintenance system in one package. From loosening rusted bolts to protecting electrical contacts, from lubricating mechanisms to repelling water, it handles the tasks that keep equipment running.
For Pakistani workshops, factories, and homes, Multispray is the one can you’ll always want within reach.
Call to Action
Ready to simplify your maintenance with one versatile product?
Contact PATSA Pakistan:
· Find Multispray at your local dealer
· Get bulk pricing for workshops and factories
· Learn about our complete maintenance range
· Request technical information
PATSA Pakistan — One Spray, Endless Solutions.
